Can I Set Up A Bathtub Myself?
Can I Set Up A Bathtub Myself?
Blog Article
What are your ideas on Installing A Bathtub?

Mounting a bath tub isn't precisely rocket science, however it does require solid plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a brand-new one is additionally a moderately difficult job. If the old tub is conveniently easily accessible, the project can move immediately; if you have to open a wall surface to remove the old tub and also place the new tub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly require a helper to vacate the old tub and set in the brand-new one. See to it you have actually certified yourself for the task as well as are comfortable attempting it. As opposed to employing a contractor to take over a halfway-completed job, it is far better to take into consideration using one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This article will certainly help you install a brand-new bathtub in your shower room if you have actually currently acquired a new tub and don't need to transform the plan of your previous water pipelines.
Your devices and material list should consist of the following:
Preparing for the Installation
Firstly, the supporting structure provided with the bathroom should be fitted (if called for) according to the manufacturer's instructions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to see to it that if the tap includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps unit to stop stress on the bath tub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must now be ready to be fitted in its final placement.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water system. After doing so, activate the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be rather problematic due to the restricted access that is usually the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a fabric ready for the staying water that will come from the pipes. Once the supply pipelines have been removed, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from transforming during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
Before going on to fit the brand-new faucets, contrast the pipe links on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Setting up the Tub
Making use of the two wood boards under its feet, put the tub in the called for setting. The wooden boards are useful in evenly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four tiny points.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by checking the spirit level and also changing the feet on the bathtub until the spirit level checks out degree.
To install taps, fit all-time low of the furthest versatile tap adapter to the suitable supply pipeline by making a compression join; then do the same for the various other faucet.
Turn on the supply of water and also examine all joints as well as brand-new pipework for leakages and tighten them if essential. Load the bath tub and likewise inspect the overflow outlet as well as the regular outlet for leaks.
Ultimately, deal with the bath paneling as defined in the manufacturer's user's manual. Tiling and sealing around the bath tub should wait until the bathtub has actually been used a minimum of once as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the tap and the other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in location in between the faucet and also the sink. Safeguard the tap in position with the supplier provided backnut. As soon as the tap is safely in position, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap adapters. The previous type should be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to fracture an inflexible seal, creating the water to pass through the wall surface between the bathroom and also the tiling, resulting in issues with moisture and possible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes and cartridges, and can sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill the bath tub with water prior to sealing, to permit the activity experienced when the bathtub is in use. The sealer can break fairly very early if you do not consider this movement before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the market. It is advisable to fit the ceramic tiles making use of water-resistant or water-proof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

As an avid person who reads about How to Install a Bathtub, I imagined sharing that article was really helpful. Are you aware of someone else who is sincerely interested in the topic? Feel free to share it. Thank you so much for your time invested reading it.
Click For More Information
Report this page